B2601
Low Severity (Level 1)No Latch Signal Sensed on Closing and Door Reversed
B2601 usually means no Latch Signal Sensed on Closing and Door Reversed.
Can you still drive with B2601?
✅Safe to drive — this is an informational or minor issue. Schedule diagnosis at your convenience.
Typical repair cost: $80 – $500
Severity Level 1 — Low
This code indicates a minor issue that is unlikely to cause immediate driveability problems. You can typically continue driving but should have the vehicle inspected at your earliest convenience.
Common Symptoms
- Power door locks not responding to key fob or interior switch
- Door locks cycling (locking/unlocking) on their own while driving
- Diagnostic trouble code (DTC) stored in module memory
- Fault may be intermittent — code may clear itself and reappear
- Reduced vehicle functionality related to the power door lock/latch system
Possible Causes
- Faulty door lock actuator — most common cause, test before replacing
- Damaged or corroded wiring/connector in the power door lock/latch system circuit
- Blown fuse or faulty relay for the power door lock/latch system
- Poor ground connection — check and clean all related ground points
- Control module fault — rare but possible, only consider after ruling out simpler causes
- Broken wire in the door jamb wiring boot — harness flexes every time the door opens, eventually wires break inside the rubber boot
Common Fixes
- Scan vehicle with a professional-grade OBD2 scanner to read all stored codes and freeze frame data — note the conditions when the code set ($44-111 at shop, free at auto parts store for basic scan)
- Visually inspect the power door lock/latch system wiring harness and connectors — look for chafed wires, melted insulation, green corrosion, loose pins, or rodent damage (often free to check yourself, $120 diagnostic fee at shop)
- Inspect the wiring boot where it passes from the body into the door — this is the #1 failure point. Peel back the rubber boot and check for broken/cracked wires ($0 DIY inspection)
- Replace door lock actuator if testing confirms it has failed — use OEM quality, avoid the cheapest no-name aftermarket parts that fail in a year ($80-500)
- Check and replace any blown fuses in the power door lock/latch system fuse circuit — if fuse blows again, there's still a short that needs to be found ($2-20 for fuses)
Estimated Repair Cost
These are estimated costs based on generic repair data. Actual costs may vary depending on your vehicle, location, and labor rates.
Frequently Asked Questions
What does B2601 mean?
B2601 stands for "No Latch Signal Sensed on Closing and Door Reversed". B2601 usually means no Latch Signal Sensed on Closing and Door Reversed.
Can you drive with B2601?
Safe to drive — this is an informational or minor issue. Schedule diagnosis at your convenience.
How much does it cost to fix B2601?
Repair costs for B2601 typically range from $80 to $500, depending on your vehicle make, model, and local labor rates. Common fixes include: Scan vehicle with a professional-grade OBD2 scanner to read all stored codes and freeze frame data — note the conditions when the code set ($44-111 at shop, free at auto parts store for basic scan); Visually inspect the power door lock/latch system wiring harness and connectors — look for chafed wires, melted insulation, green corrosion, loose pins, or rodent damage (often free to check yourself, $120 diagnostic fee at shop); Inspect the wiring boot where it passes from the body into the door — this is the #1 failure point. Peel back the rubber boot and check for broken/cracked wires ($0 DIY inspection).
Will B2601 clear itself?
Explore Repair Costs
Related OBD-II Codes
These codes are in the same range as B2601 and often share similar causes and fixes.
Worried about repair costs?
Get transparent estimates and verify your mechanic's quote before authorizing repairs.
Related Discussions
See what other car owners are saying about this code and related repairs.
View B2601 discussions in the community